Table of Content
Then, use cutting shears to make these layers. You can prevent split ends, in part, by using cutting shears instead of standard scissors when making layers. Otherwise, the layers will be too short, and you’ll fight with runaway wispy hair strands. Use a vertical movement to cut the hair starting at the hairline and up towards the top of the client’s head.
For visual learners, it might help to watch a few YouTube tutorials before beginning. It's finally time to start snipping away. To begin, use the fine tooth end of your cutting comb to bring forward a small quarter inch section of hair from each side of your natural parting. Carefully bring that down to your starting point, pull it out slightly so you can view what you're doing with more accuracy, and begin to gently glide your shears down the hair. You will not be closing your shears, or dragging them, but slide cutting your way down the hair.
Shortcut Haircut: Hair Hack in Layering Your Tresses
I believe in a dry cut, no matter what type of texture you have. The key to doing this properly is making sure the hair and scalp are clean. This will ensure there is no product build-up or sebum weighing the hair down at the roots, which would cause the hair to lay differently after it's washed. So make sure your hair has been recently washed and is free of all products. Alternatively, slide your fingers down instead of the elastic.
Use the travelling guide, the most recently cut segment of hair, to measure the length of the next segment. Insert the traveling guide and the next segment of hair between your forefinger and middle finger. Move the fingers towards the ends—pulling the hair at a 90° angle—until you reach the end of the traveling guide. Cut the new segment of hair so that it is the same length as the traveling guide. Your preference in hair length is significant since it will affect your whole appearance. Most layered cuts are short-length or shoulder-length haircuts, such as bobs and lobs.
Wall and hand mirrors
For starters, cut only 1 to 2 inches (2.5 to 5 cm) and then, if still necessary, continue cutting. Take a small strand of hair from the center of the lower section. Slide your fingers to the tip until you reach the point where you want to cut and trim the excess hair. Cut the rest of the section using the mobile guide. Use the first layer as a guide to determine the length of the second layer.
Now, I would recommend never cutting your length above the chin. Following this advice will ensure that your shortest layer falls no higher than your jawline. If you desire to have a longer fringe or side bang, I'd suggest leaving those bits out and blending them into your layers after the bulk of your hair is cut. Then, determine how much length you want to cut off. If you aren't sure, start small with 1/2" or 1" . If you don't cut enough off the first time around, you can always go back through this process again because well, you can always go shorter.
Section Your Hair
Moisten your hair again with the water in the bottle when it starts to dry. You can also skip the wash and simply use the bottle with water to moisten it. Use the spray bottle to re-wet your hair when it starts to dry.
Use your cutting comb to direct all the hair forward, over your face and pinch out one tiny subsection at a time, each one beneath the other. Taking small subsections and a gentle approach with this cutting method will give you the most control over what you're doing as a beginner. But speaking as a stylist, I can confidently say that cutting your own face-framing layers is easy-to-achieve and can give your haircut a huge boost . Keep reading for our 10-step guide on how to cut the perfect face-framing layers at home. Before cutting someone's hair, you can buy a hair demonstration model at a local beauty supply store. Try cutting subtle layers, more dramatic layers and layers on mid-length and short hair before working on anyone's real hair.
Section your hair
Repeat the process until the entire section is cut. Divide, comb, and clip the remaining hair at the nape of the neck into a left and a right section. Create a part on each side of the head along the parietal ridge—approximately 4 finger widths above the tops of your ears.
Lift your hair at a ninety-degree angle from your head and hold it straight between your forefinger and middle finger. Keeping your hair between your fingers, bring it down in front of your face. Slide your fingers toward the tips of your hair until they are level with the place where you want your shortest layers to start. Trim the length of hair sticking out from between your fingers. It would be best to trim your hair's back portion to achieve a finished layered look.
If you notice more breakage or split ends, it could be cut as frequently as every six to eight weeks. Be specific with your hairstylist when you’re getting your haircut. The last strand of hair you cut in one section becomes the new mobile guide. This is held next to the next strand of hair and used as a ruler.
Gather a small segment of hair at the front left side to use as your first guide. You should angle the short layers at the top of your head at a 135 – 180-degree angle. As you move down to the longer layers at the sides, it’s okay to cut them at 90 degrees. However, you should use point cutting to blend these sharper layers into your hair.
That way, you don’t have to worry about debris and grease affecting your ability to cut smooth layers. Needless to say, that can be a pain point for a person with short hair, causing issues when you try to style it. Separate your hair into two sections with a vertical line in the center of your head, running from the top of the forehead to the base of the skull.
Remove a ½ inch section of hair along the perimeter of the hair line. Part the hair down the center of the crown. To isolate the left and right crown sections, part the hair horizontally from just behind the ear to the center part. Don’t beat yourself up for finding choppy sections of layers you made—they happen to the best of us, hairdressers included. Therefore, consider using hair products with UV filters to protect your layers from damage. Choosing an appropriate size shear depends on a combination of your hand size and personal preference.
How to trim your hair wet
It’s up to you and your planning regarding how many layers you want to incorporate into your hair. But however many you end up doing, try your best to keep those layers even. Pull your hair into a ponytail on top of your head. To glide your shears down safely, you want to subtly pulse your two fingers as they make their way down.
No comments:
Post a Comment